Uprev ARC Licence
The UpRev ARC (Advanced Racing Controls) License will enable 2-Step (MT), Flatfoot Shifting (MT), Rolling Anti-lag (AT,MT) and Burn-out Mod (MT,AT). ARC support is currently available for 2003 and up 350Z, G35, 370Z, and G37.
ARC 2-Step Launch Control - This feature makes it possible to have more controlled launches and for building boost off the line. You must be in first gear with the clutch engaged to activate 2-Step Launch Control. In the ROM Editor you can set your Launch RPM, this can also be adjusted on the fly using the cruise toggle on the steering wheel, the base ROM is set to 3200 RPM. In the Editor, you can also adjust the minimum throttle voltage required to activate 2-Step Launch Control, the base ROM is set to 3.8 Volts, which is fairly close to WOT - in order for the feature to activate the throttle voltage must be greater than what you have set. You will also see the setting Launch Vehicle Speed; the speed you choose here will be the vehicle speed that the 2-Step will disengage and the rev limiter will return to whatever you have set in the current map under Rev &Speed Limits. You will be able to set your timing target, which will take affect while 2-Step is active, the base ROM is set to -10 degrees BTDC. Lastly, you can adjust the Launch Fuel Compensation, this value is on the same scale as those found in your main Fuel Compensation map under the Fuel tab.
ARC Flat-foot Shifting - This feature makes it possible to continue holding the accelerator pedal while shifting with the clutch engaged. A temporary Rev limit will be set at (current engine + RPM jump). The RPM jump is adjustable in the Flat-foot Shifting settings, we have it set to 50 RPM in the base ROM. This feature allows for faster shifting, an extra jolt of power upon entering the next gear, and with full control of fuel and timing you can hold boost during shifts. The clutch must be engaged for Flat-foot Shifting to activate. The first setting under this tab is the Flat-foot Throttle Activation, we have it set to 3.00 Volts (roughly 3/4 throttle) in the base ROM, so that Flat-foot shifting only activates if the throttle voltage is at least 3.00 Volts. You can adjust this to your liking as well. The Flat-foot Speed Activation is the minimum vehicle speed needed to activate Flat-foot Shifting, the base ROM is set to 18 MPH, which means Flat-foot Shifting will only activate if the vehicle speed is over 18 MPH. You will also see Flat-foot Minimum RPM, this is so that you can govern the minimum RPM which Flat-foot Shifting can engage, the base ROM is set to 3000 RPM, thus the feature can only be activated if your engine speed is at least 3000 RPM - this is adjustable as well.
ARC Rolling Anti-lag - Unlike 2-Step and Flatfoot Shifting you don't need to use the clutch pedal for this feature. This feature makes it possible for more controlled rolling launches and building boost for roll racing. Like 2-Step and Flat-foot Shifting, this feature also gives you full control of fuel and timing. In the ROM Editor under the ARC Rolling Anti-lag tab, you will see Rolling Anti-lag Vehicle Speed Activation, this is the speed you must reach in order for this feature to activate, the base ROM comes set with 18 MPH, which means you must be over 18 MPH to use this feature. You will also see Rolling Anti-lag Minimum RPM, this is so that you may govern the minimum RPM which Rolling Anti-lag can engage, the base ROM is set to 3000 RPM, thus the feature can only be activated if your engine speed is at least 3000 RPM - this is adjustable as well. Lastly and most importantly, in order to activate Rolling Anti-lag you must meet the minimum throttle activation requirement, the base ROM comes set to 2.00 Volts, which means you must be about 1/2 throttle for the feature to activate - you may adjust this value as well. To activate Rolling Anti-lag be sure all the above requirements are met, then hold down the Cancel cruise button once you get to the desired vehicle speed for your roll, release the Cancel button when you want to go.